Ramsey Patch Integrator 4.2.3 with the EFI preset
Windows XP Professional SP3 x86 Integral Edition 2025.8.19 (Vanilla)

1. Extract the whole ZIP into a short writable directory such as C:\XPBuild.
   Place your original Ramsey (Vanilla).iso beside Options Menu.cmd or in
   its parent directory. Leave the original filename on the source.
   Allow space for the source, the unpacked work tree, xp.iso and a
   further 2,000,000,000 bytes when building usb.img.

2. Run Options Menu.cmd. Press S once to load the EFI preset. YES marks
   1, 3, 5, 9, A, C, E, F, S and T. You can change the selections before
   pressing Z. Pressing S again restores your earlier manual selections.

   1  Kai SATA/AHCI with Storport
   2  Microsoft NVMe
   3  Microsoft USB 3.x xHCI
   4  Project eMMC driver 1.5.0.2 (mmc105.zip)
   5  Project ACPI when S is selected
   9  NVMe2K 2.2
   A  Kernel-Mode Driver Framework 1.11
   C  Ramsey PM/RTC timer fix
   E  Ramsey Live USB settings
   F  Remove DriverPacks BASE and its driver packs
   S  EFI preset
   T  usbimg

   Microsoft NVMe and NVMe2K are alternative drivers for the same NVMe
   class. Press 2 for Microsoft or 9 for NVMe2K. The menu clears the other
   selection. The build prints a line for NVMe2K at selection, integration
   and file verification. For the project eMMC driver from mmc105.zip,
   press S, then 4, then Z. The SYS and INF are the x86 FRE 1.5.0.2 pair.

3. Press Z to build. The EFI preset creates xp.iso beside Options Menu.cmd.
   With T on, it then creates usb.img containing that exact xp.iso. With T
   off, the build ends after xp.iso. Move an earlier output before rebuilding.

   You can also use the command prompt. The two output directories must exist.
     EFI\Build.cmd "D:\Sources\Ramsey (Vanilla).iso" "D:\Out\xp.iso" "D:\Out\usb.img"
     EFI\Build.cmd "D:\Sources\Ramsey (Vanilla).iso" "D:\Out\xp.iso" /iso-only

   To make the USB image later from an existing prepared ISO, run
     EFI\UsbImage.cmd "D:\Out\xp.iso" "D:\Out\usb.img"

4. Write usb.img to a spare USB stick in raw image mode and boot its x64
   UEFI entry. For a new installation, choose 4, Prepare SSD. The screen
   lists the internal drives with size and model. Type the target's name,
   then type the displayed LOESCHEN command to confirm erasing that drive.
   The USB source is excluded. Enter with an empty selection cancels.

   For drives with 512-byte logical sectors (including 512e), preparation
   creates and formats both primary MBR partitions before Windows starts.
   P1: visible FAT32 LBA, type 0x0C, 100 MiB, start sector 2048 (1 MiB).
   P2: NTFS, type 0x07, active, from sector 206848 (101 MiB) to the last
   sector. Both starts are multiples of 2048 sectors. The tool copies
   EFI\BOOT\BOOTX64.EFI from the stick to P1 and verifies it byte for byte
   after remounting P1. It leaves the preparation tools on the stick.

5. Press R and boot the USB again. Choose 1, TXT Setup. Type the internal
   disk number and press Enter, even if only one disk is listed. In the
   blue XP partition list select the large second partition labelled XP.
   Use "Leave the current file system intact" when offered. Keep both
   partitions in place. If the disk already has this layout and NTFS,
   start here to preserve the partition table.

   After TXT file copy and restart, boot the USB again, choose 2, GUI Setup,
   and select the same physical disk. The loader verifies the EFI copy.
   After installation, use the internal drive's EFI\BOOT\BOOTX64.EFI
   to start XP without the USB. Firmware with a manual boot-file selector
   can use this path on the visible FAT32 volume. The blue text stage
   requests 640 x 480. Installed XP uses the firmware display mode.

The EFI preset targets XP Professional SP3 x86. BOOTX64.EFI refers to the
firmware architecture. An XP x64 install requires its own media and drivers.
